Coarse Aggregate: Sizes, Grading, Tests and Limits as per IS 383

Quick answer: Coarse aggregate is the crushed stone or gravel retained on the 4.75 mm IS sieve. It makes up about 60 to 75% of the volume of concrete. The common nominal sizes are 10, 12.5, 20 and 40 mm; 20 mm angular crushed stone is the usual choice for reinforced concrete. Its size, grading, shape and cleanliness decide the strength and workability of the concrete.

Coarse aggregate is the skeleton of concrete, so poor aggregate gives poor concrete however good the cement is. This guide explains the types, sizes, grading, tests and site checks, and works out a real quantity example. It follows IS 383 (aggregates for concrete) and the IS 2386 test methods. For the finer material, read grades of sand.

What is coarse aggregate?

In simple words: Aggregate is the rock part of concrete. Coarse aggregate is the larger part, the pieces that stay on a sieve with 4.75 mm openings. Anything that passes through is fine aggregate (sand). Cement paste coats the stones and glues them together.

Where you see it: Every batching plant and site has stockpiles of 10 mm and 20 mm stone beside the sand and the cement. The stone is brought from a crushing plant where quarried rock is crushed and screened.

Civil Site Engineer Bundle — Concrete QC Handbook + RCC Lap Length Excel cover
📚 Recommended Download
Civil Site Engineer Bundle — Concrete QC Handbook + RCC Lap Length Excel
Our two best-sellers in one download: the 238-page Concrete Site Handbook kit plus the IS 456 lap-length Excel toolkit and quick-reference PDF.
✔ IS 456 based  ·  ✔ Instant download  ·  ✔ Lifetime access
₹1098₹299
Get the Bundle →
Quarry crushing plant with conveyors and stockpiles of aggregate
Rock is crushed and screened into different sizes at a crushing plant.

Types of coarse aggregate

TypeDescriptionNotes for concrete
Crushed stoneQuarried rock (granite, basalt, limestone) crushed to size. Angular, rough facesBest bond with the cement paste. The usual choice for structural concrete
Natural gravelRounded stones from river beds or gravel pitsWorkable, but the smooth surface bonds less well. Needs washing
Crushed gravelGravel that has been crushed to break the rounded facesBetween the two
Recycled aggregateCrushed old concrete. See recycled aggregatesHigher absorption. Needs mix adjustment
Lightweight aggregateExpanded clay, shale or similarUsed where a lighter concrete is needed

Stone types are described in types of stones in construction.

Particle shape

Shape matters as much as size. Angular, cubical pieces interlock and bond well. Flat or long pieces trap water and weaken the concrete. IS 2386 Part 1 defines a flaky particle as one whose thickness is less than 0.6 of its mean sieve size, and an elongated particle as one whose length is more than 1.8 of its mean size. The code limits the combined share of these pieces, so check the current IS 383 value for your project.

Diagram of rounded, angular, flaky and elongated aggregate particles and the 4.75 mm sieve
Particle shapes and where coarse aggregate starts on the IS sieves.

Sizes of coarse aggregate and where they are used

Nominal sizeTypical use
10 mmThin slabs, small precast units, narrow sections, and blending with 20 mm for grading
12.5 mmMedium sections with closely spaced bars
20 mmGeneral reinforced concrete: beams, columns, slabs and footings
40 mmMass concrete, plain cement concrete under footings, and wide sections with widely spaced bars

The maximum size must suit the member. IS 456 limits the nominal maximum size to not more than one quarter of the smallest dimension of the member, and to 5 mm less than the minimum clear spacing between bars or the cover, whichever is smaller. A larger stone in a congested section causes honeycombing.

Where you see it: A 150 mm thick slab uses 20 mm stone at most (150 / 4 = 37.5 mm is the upper limit, and the bar spacing and cover usually govern). A heavily reinforced column with 40 mm clear spacing between bars should not take 40 mm stone.

Grading of coarse aggregate

In simple words: Grading means the mix of sizes in the stockpile. A well graded aggregate has pieces of several sizes, so the smaller ones fill the gaps between the bigger ones. That leaves fewer voids, so less cement paste is needed.

Grading is found by a sieve analysis (IS 2386 Part 1). A dry sample is shaken through a stack of IS sieves and the percentage passing each sieve is calculated. IS 383 gives limits for graded aggregate and single-sized aggregate. Typical limits for the most common sizes are shown below; always check them against the current edition of IS 383.

IS sieve size20 mm graded: % passing20 mm single size: % passing
40 mm100100
20 mm95 to 10085 to 100
10 mm25 to 550 to 20
4.75 mm0 to 100 to 5

Properties and tests

TestIS 2386 partWhat it tells you
Sieve analysisPart 1Grading: the mix of sizes
Flakiness and elongation indexPart 1How many flat or long pieces are present
Specific gravity and water absorptionPart 3Density of the stone and how much water it soaks up
Bulk density and voidsPart 3Weight per cubic metre, used to convert volume to weight
Aggregate crushing valuePart 4Resistance to a slowly applied load
Aggregate impact valuePart 4Toughness against sudden blows
Los Angeles abrasionPart 4Resistance to wear, important for road surfaces and floors
SoundnessPart 5Resistance to weathering, tested with sodium or magnesium sulphate
Deleterious materialsPart 2Clay, silt, coal, shale and similar harmful matter

IS 383 sets limits for the impact and crushing values: commonly 45% for aggregate used in concrete other than wearing surfaces, and 30% for wearing surfaces such as industrial floors and roads. A lower value means a tougher stone. Typical specific gravity is about 2.6 to 2.8, and the bulk density of 20 mm stone is usually around 1,450 to 1,600 kg/m³.

How coarse aggregate affects concrete

  • Size: a larger maximum size needs less paste and water for the same workability, so it suits mass concrete.
  • Shape: angular stone gives better bond but needs a little more paste than rounded stone.
  • Grading: good grading reduces voids, so concrete is denser and cheaper.
  • Strength of the stone: the concrete cannot be stronger than the stone it is made with.
  • Cleanliness: dust, clay and silt coat the stone and weaken the bond.
  • Water absorption: porous stone takes water out of the mix. See water-cement ratio.

Worked example: coarse aggregate for 10 m³ of M20 concrete

Example. A nominal mix of M20 (1 : 1.5 : 3, cement : sand : coarse aggregate by volume) is used for 10 m³ of concrete. Find the volume and weight of coarse aggregate. Assume dry volume = 1.54 × wet volume, and a bulk density of 1,500 kg/m³.

  • Dry volume of materials = 1.54 × 10 = 15.4 m³
  • Sum of the parts = 1 + 1.5 + 3 = 5.5
  • Coarse aggregate volume = 15.4 × 3 / 5.5 = 8.4 m³
  • Weight = 8.4 × 1,500 = 12,600 kg, about 12.6 tonnes

Add a wastage allowance on top. For mix ratios of other grades see M5 to M40 concrete mix ratios, and use the concrete calculator or gravel calculator for quick quantities. The process of making and placing concrete is covered in concrete manufacturing process.

Wheel loader loading a truck from aggregate stockpiles at a yard
Stockpiles at an aggregate yard are kept separate by size.

Storage and handling on site

  • Keep each size in its own stockpile, separated by walls or bays, so sizes do not mix.
  • Stack on a clean, hard, drained base, not directly on soil, so the stone stays clean.
  • Avoid dropping from a height; it causes segregation, with the big pieces rolling to the edge.
  • Check surface moisture on wet days and adjust the water in the mix.
  • Do not let sand, clay or rubbish mix into the stockpile.

Site checks before using a lot

  • Look for dust, clay balls and soft or weathered pieces.
  • Check the size range against the order (a 20 mm lot should not be full of 40 mm stones or of fine dust).
  • Look for flat and long pieces. A handful should look mostly cubical.
  • Ask for the supplier’s test reports (sieve analysis, impact or crushing value) for important work.
  • Test a sample by sieve analysis if the lot looks different from the last delivery.

Frequently asked questions

What is the size of coarse aggregate?

Coarse aggregate is any aggregate retained on the 4.75 mm IS sieve. The common nominal sizes are 10, 12.5, 20 and 40 mm.

Which coarse aggregate is used for RCC?

Angular crushed stone of 20 mm nominal size is the usual choice for reinforced concrete. The maximum size is limited by the bar spacing, the cover and the member thickness.

What is the difference between coarse and fine aggregate?

Coarse aggregate is retained on the 4.75 mm sieve; fine aggregate (sand) passes through it. Coarse aggregate forms the bulk of the concrete, while sand fills the gaps between the stones.

Can river gravel be used instead of crushed stone?

Yes, if it is clean and sound, but rounded gravel bonds less well than angular crushed stone. Crushed gravel, or washed and tested gravel, is acceptable for many jobs.

How is the weight of coarse aggregate found?

Find the volume from the mix ratio, then multiply by the bulk density, which is usually about 1,450 to 1,600 kg/m³ for 20 mm stone. The worked example above shows the steps.

Stop calculating by hand — go Pro

Unlock an ad-free experience plus a growing library of ready-to-use civil-engineering calculators, IS-code cheat-sheets and formula PDFs. From just ₹99.

Go Pro →
Fuel Free Learning Support TheCivilStudies

Keep civil engineering knowledge free — articles, calculators, and practical site guides for everyone.

Choose an amount

100% Secure · Powered by Cashfree

TheCivilStudies Team
TheCivilStudies Team

TheCivilStudies is an independent civil-engineering learning site from India. Our guides explain IS-code provisions, formulas, worked examples and site practice for students and working site engineers. Calculations are checked against the relevant Indian Standard, and articles are updated when codes or practice change. Spotted an error? Tell us in the comments and we will fix it.

Articles: 466