Lean Concrete (PCC): Mix Ratio, Thickness, Uses and Quantity

Quick answer: Lean concrete is a weak, plain (unreinforced) concrete with a low cement content, such as M7.5 (1 : 4 : 8) or M10 (1 : 3 : 6). It is laid in a thin layer, usually 75 to 150 mm thick, under footings, floors and pavements to give a level, clean working surface. It is also called plain cement concrete (PCC) or blinding. It is not a structural member: the footing above carries the load.

Lean concrete is the first layer of concrete in most foundations, and it is easy to get wrong because it looks unimportant. A poor lean layer makes the footing steel dirty, the levels uneven and the cover unreliable. This guide explains what it is, why it is used, the usual mixes and thickness, how to lay it and how to work out quantities. For the stone layer that sometimes goes under it, read soling in foundation.

What is lean concrete?

In simple words: Lean means low in cement. Ordinary structural concrete has plenty of cement to give strength. Lean concrete has much less, because it is not asked to carry load. It is a flat, clean bed on which the real foundation is built.

Where you see it: At the bottom of every footing trench, where a plain grey layer is laid and levelled before the steel is fixed. The same layer is placed under floor slabs, and as a base under concrete roads (dry lean concrete).

Civil Site Engineer Bundle — Concrete QC Handbook + RCC Lap Length Excel cover
📚 Recommended Download
Civil Site Engineer Bundle — Concrete QC Handbook + RCC Lap Length Excel
Our two best-sellers in one download: the 238-page Concrete Site Handbook kit plus the IS 456 lap-length Excel toolkit and quick-reference PDF.
✔ IS 456 based  ·  ✔ Instant download  ·  ✔ Lifetime access
₹1098₹299
Get the Bundle →
Plain concrete beds and formwork at foundation trenches before footings
Plain concrete beds and formwork at foundation trenches before footings are cast.

Why lean concrete is used

Diagram of a lean concrete layer under an RCC footing, with thickness and projection
Where lean concrete sits under a footing.
  • Level, clean bed. Bars and formwork are fixed on a flat surface, so the footing thickness is accurate.
  • Stops loss of water and cement. Without it, the soil would suck the water and fine cement out of the footing concrete.
  • Keeps steel off the soil. Cover blocks stand on the hard surface instead of sinking into mud.
  • Marks the layout. Column and wall centre lines can be marked on the surface.
  • Protects from wet ground. It separates fresh concrete from groundwater and dirty soil.

Lean concrete mix ratios

GradeNominal mix (cement : sand : coarse aggregate)Typical use
M7.51 : 4 : 8Blinding under footings and slabs, filling
M101 : 3 : 6Blinding where a stronger bed is wanted, plain concrete work
M151 : 2 : 4Plain concrete in heavier or more exposed work

These are nominal mixes by volume. IS 456 lists M10 and M15 as plain concrete grades, and weaker mixes such as M7.5 are common in practice for blinding. Always follow the mix and grade written in the project drawings and specification. The stone is usually 40 mm or 20 mm graded aggregate; see coarse aggregate sizes and grading, and M5 to M40 concrete mix ratios for other grades.

Thickness and size

The layer is usually 75 to 150 mm thick, and 100 mm is common under footings. It should extend beyond the edge of the footing on every side, typically by about 75 to 150 mm, so there is room for formwork and a clean working edge. A layer that is too thin cracks and breaks up while the steel is being fixed on it.

Workers on a reinforcement grid laid in a foundation excavation
Reinforcement being laid in a foundation excavation.

Lean concrete compared with soling and RCC

SolingLean concrete (PCC)RCC footing
What it isHand-packed stone layerWeak plain concreteReinforced concrete
PurposeFirm, drained baseLevel, clean bedCarries the structural load
ReinforcementNoneNoneYes
Typical thickness150 to 230 mm stones75 to 150 mmFixed by design

The soling and lean concrete are not always both used. The project drawings say which layers apply. See foundation types and shallow foundations for where the layer fits.

How to lay lean concrete: step by step

  1. Prepare the base. Excavate to the right level, remove loose soil and water, and compact the bed. Add soling if the drawings call for it.
  2. Fix level pegs and edge forms. Mark the top level of the layer with pegs or formwork.
  3. Wet the base lightly. A dry soil bed drinks water out of the concrete; keep it damp but without puddles.
  4. Mix to the specified ratio. Measure the cement, sand and stone with gauge boxes. Do not add extra water to make it easier to spread.
  5. Place and spread. Tip the concrete, spread it evenly to the pegs and compact it.
  6. Level and finish. Screed the top flat with a straight edge. It does not need a smooth finish.
  7. Cure. Keep it damp for a few days. Leave it until it has hardened enough to be walked on before fixing the steel.

Worked example: materials for lean concrete under 12 footings

Example. Twelve footings are each 1.5 m × 1.5 m. A 100 mm thick M7.5 (1 : 4 : 8) lean concrete layer is laid under each, extending 100 mm beyond the footing on every side. Find the cement, sand and stone needed. Assume dry volume = 1.54 × wet volume, and 1 bag of cement (50 kg) = 0.0347 m³.

  • Size of each layer = 1.5 + 0.1 + 0.1 = 1.7 m square, so volume = 1.7 × 1.7 × 0.1 = 0.289 m³
  • Total wet volume = 12 × 0.289 = 3.47 m³
  • Dry volume = 1.54 × 3.47 = 5.34 m³; sum of the parts = 1 + 4 + 8 = 13
  • Cement = 5.34 / 13 = 0.411 m³ = 0.411 / 0.0347 = about 12 bags
  • Sand = 4 × 0.411 = about 1.64 m³
  • Coarse aggregate = 8 × 0.411 = about 3.29 m³

Add an allowance for wastage and for uneven excavation. Sand bulks when damp; see bulking of sand. For quick estimates, use the concrete calculator and see cement bags per cubic metre of concrete.

Common mistakes

  • Too thin: under about 50 mm it cracks and crumbles when workers and steel load it.
  • Too wet: extra water makes a weak, dusty surface and a slurry that washes out.
  • Placed on loose or muddy soil: the layer settles unevenly. Compact the base first.
  • Not extended beyond the footing: no room for formwork and the footing edge sits on bare soil.
  • Steel fixed too soon: bars and cover blocks sink into green concrete.
  • Treating it as structure: lean concrete is not part of the footing depth in the design.

Frequently asked questions

What is lean concrete?

Lean concrete is plain concrete with a low cement content, laid as a thin base layer under footings, floors and pavements. It is also called PCC or blinding concrete.

What is the mix ratio of lean concrete?

Common mixes are M7.5 (1 : 4 : 8) and M10 (1 : 3 : 6) by volume. The project specification fixes the exact grade.

How thick should lean concrete be?

Usually 75 to 150 mm, with 100 mm common under footings. It should extend beyond the footing edge on all sides.

Is lean concrete structural?

No. It carries no design load. It gives a level, clean surface for the footing, and the footing above is designed to carry the load.

What is the difference between lean concrete and PCC?

The two terms are used for the same thing in most site work. Lean concrete refers to the low cement content, and PCC (plain cement concrete) refers to the fact that it has no reinforcement.

Stop calculating by hand — go Pro

Unlock an ad-free experience plus a growing library of ready-to-use civil-engineering calculators, IS-code cheat-sheets and formula PDFs. From just ₹99.

Go Pro →
Fuel Free Learning Support TheCivilStudies

Keep civil engineering knowledge free — articles, calculators, and practical site guides for everyone.

Choose an amount

100% Secure · Powered by Cashfree

TheCivilStudies Team
TheCivilStudies Team

TheCivilStudies is an independent civil-engineering learning site from India. Our guides explain IS-code provisions, formulas, worked examples and site practice for students and working site engineers. Calculations are checked against the relevant Indian Standard, and articles are updated when codes or practice change. Spotted an error? Tell us in the comments and we will fix it.

Articles: 466