Fluid mechanics is a scoring subject because it runs on a handful of ideas: pressure increases with depth, what flows in must flow out, and energy is conserved along a streamline. Almost every formula in the subject is one of these three ideas written for a particular case.
The topics follow the order of the official GATE Civil Engineering syllabus under Water Resources Engineering. Unless stated, the fluid is water with density ρ = 1000 kg/m³ and specific weight γ = 9.81 kN/m³. For the other subjects, see the GATE, ESE and SSC JE preparation guide.
What the syllabus asks
| Exam | Syllabus wording |
|---|---|
| GATE CE, Fluid Mechanics | Properties of fluids, fluid statics; continuity, momentum and energy equations and their applications; potential flow, laminar and turbulent flow; flow in pipes, pipe networks; concept of boundary layer and its growth; concept of lift and drag |
| GATE CE, Hydraulics | Forces on immersed bodies; flow measurement in channels and pipes; dimensional analysis and hydraulic similitude; channel hydraulics: specific energy, critical flow, hydraulic jump, uniform flow, gradually varied flow |
| ESE Civil Paper II | Flow of fluids, hydraulic machines and hydro power: fluid properties, pressure, thrust, buoyancy, flow kinematics, flow measurement, laminar and turbulent flow, pipe flow, open channel flow, pumps and turbines |
| SSC JE, Hydraulics | Fluid properties, hydrostatics, measurement of flow, Bernoulli’s theorem and its application, flow through pipes, flow in open channels, weirs, flumes, spillways, pumps and turbines |
1. Properties of fluids
In simple words: A fluid is anything that flows: it keeps deforming as long as a shear force acts on it. Its important properties are how heavy it is (density), how “thick” it is (viscosity), and how its surface behaves (surface tension).

Where you see it: Viscosity decides how much pumping power a pipeline needs. Capillary action, a surface tension effect, is what pulls ground moisture up into a brick wall, and it is the reason a damp proof course is laid at plinth level.
| Quantity | Formula or value |
|---|---|
| Specific weight | γ = ρ g |
| Specific gravity | Density of the fluid / density of water |
| Newton’s law of viscosity | τ = μ (du/dy) |
| Kinematic viscosity | ν = μ / ρ |
| Units | 1 poise = 0.1 Pa·s; 1 stoke = 10−4 m²/s |
| Bulk modulus | K = −dp / (dV/V) |
| Excess pressure in a liquid droplet | p = 4σ / d |
| Excess pressure in a soap bubble | p = 8σ / d |
| Capillary rise in a tube | h = 4σ cos θ / (ρ g d) |
- A Newtonian fluid, such as water or air, has a constant viscosity. Fluids such as paint, blood and fresh concrete are non-Newtonian.
- When temperature rises, the viscosity of a liquid falls and the viscosity of a gas rises.
- Water rises in a glass tube because the contact angle is nearly zero. Mercury is depressed because its contact angle is more than 90°.
Example. Find the capillary rise of water in a clean glass tube of 2 mm diameter. Take σ = 0.073 N/m and θ = 0.
- h = 4σ / (ρ g d) = 4 × 0.073 / (1000 × 9.81 × 0.002) = 0.0149 m.
- The water rises about 15 mm. Halve the diameter and the rise doubles, which is why fine pores in masonry lift moisture so high.
2. Fluid statics: pressure and forces on surfaces
In simple words: In a fluid at rest, pressure depends only on depth. It is the same in all directions at a point, and it does not depend on the shape of the container.
Where you see it: The wall of a water tank and the face of a dam are thicker at the bottom because pressure grows with depth. The total push on a gate, and the point where it acts, decide the size of the gate and its hinges.
| Quantity | Formula or value |
|---|---|
| Pressure at depth h | p = ρ g h = γ h |
| Absolute pressure | Gauge pressure + atmospheric pressure |
| Standard atmosphere | 101.3 kPa = 10.33 m of water = 760 mm of mercury |
| Force on a plane surface | F = γ A h̄, where h̄ is the depth of the centroid |
| Depth of the centre of pressure | h* = h̄ + IG sin²θ / (A h̄) |
| Buoyant force | Weight of the fluid displaced |
| Metacentric height | GM = I / V − BG |
- The centre of pressure is always below the centroid of the surface.
- For a vertical rectangle with its top edge at the water surface, the force acts at two-thirds of the depth.
- A floating body is stable when the metacentre M is above the centre of gravity G, that is, when GM is positive.
Example. A vertical gate 2 m wide and 3 m deep has its top edge at the water surface. Find the force on it and where the force acts.
- Area A = 2 × 3 = 6 m². Depth of centroid h̄ = 1.5 m.
- F = γ A h̄ = 9.81 × 6 × 1.5 = 88.3 kN.
- IG = 2 × 3³ / 12 = 4.5 m⁴, so h* = 1.5 + 4.5 / (6 × 1.5) = 2.0 m below the surface, which is two-thirds of the depth.
The same calculation, on a much larger scale, gives the water thrust on a dam. See gravity dam design and stability analysis.
3. Continuity equation
In simple words: Water does not appear or disappear inside a pipe. Whatever flows in at one end must flow out at the other. If the pipe narrows, the water has to speed up.
Where you see it: A nozzle on a hose, the throat of a venturimeter and a bridge that narrows a river all speed up the flow. Under a bridge the higher velocity is what scours the bed around the piers.
| Quantity | Formula |
|---|---|
| Discharge | Q = A V |
| Continuity, incompressible flow | A1 V1 = A2 V2 |
| Continuity in two dimensions | ∂u/∂x + ∂v/∂y = 0 |
Types of flow to know: steady (does not change with time) and unsteady; uniform (does not change along the length) and non-uniform; laminar and turbulent; rotational and irrotational. Potential flow is the ideal case of irrotational flow of a fluid with no viscosity. It is described by a velocity potential φ and a stream function ψ. Lines of constant φ and constant ψ cross at right angles and together form a flow net, the same flow net used for seepage through soil.
4. Energy equation: Bernoulli’s theorem
In simple words: A flowing fluid carries energy in three forms: pressure, speed and height. If no energy is lost, their total stays the same along the flow. So where the fluid speeds up, its pressure drops.
Where you see it: Venturimeters, orifice meters and pitot tubes all measure flow by measuring this pressure change. The same effect lifts lightweight roofing sheets in a storm: fast wind over the roof lowers the pressure above it.
| Quantity | Formula |
|---|---|
| Bernoulli’s equation | p/γ + V²/2g + z = constant |
| With losses, between sections 1 and 2 | p1/γ + V1²/2g + z1 = p2/γ + V2²/2g + z2 + hL |
| Venturimeter | Q = Cd A1 A2 √(2gh) / √(A1² − A2²) |
| Pitot tube | V = √(2gh) |
| Orifice coefficients | Cd = Cc × Cv |
| Rectangular notch or weir | Q = (2/3) Cd L √(2g) H3/2 |
| Triangular (V) notch | Q = (8/15) Cd tan(θ/2) √(2g) H5/2 |
Bernoulli’s equation assumes steady, incompressible, frictionless flow along a streamline. Typical values are Cd = 0.98 for a venturimeter and about 0.62 for a sharp-edged orifice. A V-notch is more accurate than a rectangular notch for small discharges.
Example. Water flows at 2 m/s in a horizontal pipe of 200 mm diameter that narrows to 100 mm. Find the velocity in the narrow part and the drop in pressure, ignoring losses.
- The area becomes one-quarter, so V2 = 4 × 2 = 8 m/s.
- Pressure drop = ρ (V2² − V1²) / 2 = 1000 × (64 − 4) / 2 = 30 000 N/m² = 30 kPa.
5. Momentum equation
In simple words: To change the speed or the direction of a flow, a force is needed. By Newton’s third law the fluid pushes back with an equal force on whatever turned it.
Where you see it: Water turning through a pipe bend pushes the bend outward. Buried pipelines are given concrete thrust blocks at bends and tees for this reason. The same equation gives the force of a jet on a turbine bucket.
| Quantity | Formula |
|---|---|
| Force on the fluid | F = ρ Q (V2 − V1), applied in each direction separately |
| Jet striking a fixed flat plate at right angles | F = ρ a V² |
| Jet striking a plate moving away at velocity u | F = ρ a (V − u)² |
6. Laminar and turbulent flow
In simple words: In laminar flow the fluid moves in smooth layers that do not mix. In turbulent flow it tumbles and mixes. The Reynolds number, the ratio of inertia force to viscous force, tells you which one you have.
| Quantity | Formula or value |
|---|---|
| Reynolds number | Re = ρ V D / μ = V D / ν |
| Flow in a pipe | Laminar below about 2000, turbulent above about 4000 |
| Laminar flow in a pipe (Hagen-Poiseuille) | hf = 32 μ V L / (ρ g D²) |
| Velocity profile in laminar pipe flow | Parabolic; maximum velocity = 2 × average velocity |
| Friction factor in laminar flow | f = 64 / Re |
Flow in water supply pipes is almost always turbulent. Laminar flow matters for oil lines, for flow through soil, where Darcy’s law applies, and for very slow settling of fine particles.
7. Flow in pipes and pipe networks
In simple words: Water loses energy as it rubs against the pipe wall, and loses a little more at every bend, valve and change of size. This loss is called head loss, and the pump or the overhead tank must supply it.
Where you see it: The height of an overhead tank and the size of a pump are fixed by adding the head losses to the pressure needed at the last tap. A pipe that is too small wastes head; one that is too large wastes money.
| Quantity | Formula |
|---|---|
| Darcy-Weisbach friction loss | hf = f L V² / (2 g D) |
| Sudden enlargement | hL = (V1 − V2)² / 2g |
| Sudden contraction | hL = 0.5 V2² / 2g |
| Entry to a pipe | hL = 0.5 V² / 2g |
| Exit from a pipe | hL = V² / 2g |
| Pipes in series | Same discharge; head losses add |
| Pipes in parallel | Same head loss; discharges add |
| Equivalent pipe (Dupuit) | L / D⁵ = Σ(Li / Di⁵) |
| Maximum power through a pipe | When hf = H / 3 |
Some books write the friction loss as 4 f L V² / (2 g D). Their f is one-quarter of the f used here, so check which form a question uses. Pipe networks are solved by the Hardy Cross method, which corrects assumed flows until the head losses around every loop add up to zero.
Example. Water flows at 2 m/s through 300 m of 200 mm pipe. The friction factor is 0.02. Find the head loss.
- hf = f L V² / (2 g D) = 0.02 × 300 × 2² / (2 × 9.81 × 0.2) = 6.12 m.
- The supply must be at least 6.12 m higher than the outlet just to overcome friction.
8. Boundary layer
In simple words: A fluid sticks to any solid surface it touches, so its velocity there is zero. A short distance away it moves at full speed. The thin zone in between, where the velocity builds up, is the boundary layer. All the friction between the fluid and the surface happens inside it.
| Quantity | Formula or value |
|---|---|
| Reynolds number along a plate | Rex = U x / ν |
| Laminar boundary layer on a flat plate | Up to Rex of about 5 × 105 |
| Thickness of a laminar boundary layer (Blasius) | δ = 5 x / √Rex |
| Displacement thickness | δ* = ∫ (1 − u/U) dy |
| Momentum thickness | θ = ∫ (u/U)(1 − u/U) dy |
The boundary layer grows thicker along the surface and turns from laminar to turbulent. If the pressure rises in the direction of flow, the layer can separate from the surface and leave a wake of eddies behind the body. Separation is what causes the high drag on a blunt shape such as a bridge pier or a chimney.
9. Lift and drag
In simple words: A fluid flowing past a body pushes on it. The part of the push along the flow is drag. The part at right angles to the flow is lift.
Where you see it: Wind load on a tall building or a hoarding is a drag force. The settling of sand grains in a sedimentation tank is governed by drag: each grain falls at the speed where drag balances its weight.
| Quantity | Formula |
|---|---|
| Drag force | FD = CD ρ A V² / 2 |
| Lift force | FL = CL ρ A V² / 2 |
| Stokes’ law for a small sphere (Re below 1) | FD = 3 π μ d V |
In the drag formula, A is the area of the body seen from the direction of flow. Stokes’ law leads to the settling velocity used to design sedimentation tanks; see water treatment processes.
10. Open channel flow
In simple words: In an open channel the water has a free surface and flows because of the slope of the bed, not because of pressure. Rivers, canals, drains and partly full sewers are all open channels.
Where you see it: Sizing a storm drain, a canal or a culvert is an open channel problem. The hydraulic jump, a sudden rise of the water surface, is created on purpose below spillways to kill the energy of fast water before it erodes the river bed.
| Quantity | Formula |
|---|---|
| Manning’s equation | V = (1/n) R2/3 S1/2 |
| Chezy’s equation | V = C √(R S) |
| Hydraulic radius | R = A / P (area / wetted perimeter) |
| Froude number | Fr = V / √(g D), where D = A / top width |
| Specific energy | E = y + V² / 2g |
| Critical depth, rectangular channel | yc = (q² / g)1/3 |
| Minimum specific energy, rectangular channel | Ec = 1.5 yc |
| Hydraulic jump, rectangular channel | y2 / y1 = ½ [−1 + √(1 + 8 Fr1²)] |
| Energy lost in a jump | ΔE = (y2 − y1)³ / (4 y1 y2) |
| Most economical rectangular section | b = 2y, and R = y / 2 |
| Most economical trapezoidal section | Half of a regular hexagon; R = y / 2 |
- Fr less than 1 is subcritical (slow, deep) flow; Fr equal to 1 is critical; Fr more than 1 is supercritical (fast, shallow) flow.
- A hydraulic jump forms only when flow changes from supercritical to subcritical.
- Model studies of open channels use Froude number similarity. Pipe flow models use Reynolds number similarity.
Example. A rectangular channel carries a discharge of 3 m³/s per metre of width. Find the critical depth and the minimum specific energy.
- yc = (q² / g)1/3 = (3² / 9.81)1/3 = (0.917)1/3 = 0.97 m.
- Ec = 1.5 yc = 1.46 m.
Manning’s equation in use, with pipe and channel sizes, is shown in types of stormwater drainage systems and in culverts: types, parts and design points.
Common mistakes
- Using gauge pressure where absolute pressure is needed, for example when checking for cavitation.
- Using the diameter in place of the hydraulic radius. For a full circular pipe R = D / 4, not D / 2.
- Mixing the two forms of the friction formula, with f and with 4f.
- Taking the centre of pressure at the centroid of the surface. It is always lower.
- Applying Bernoulli’s equation across a pump, a turbine or a hydraulic jump without adding the energy gained or lost.
- Using the critical depth formula yc = (q²/g)1/3 for channels that are not rectangular.
Frequently asked questions
Which fluid mechanics topics are asked most in GATE?
Fluid statics, Bernoulli and continuity applications, pipe flow with losses, and open channel flow (critical depth, hydraulic jump, Manning’s equation) give most of the questions. Boundary layer and dimensional analysis usually give one short question.
Is hydraulic machinery part of the GATE civil syllabus?
No. Pumps and turbines are not in the GATE Civil Engineering syllabus. They are in ESE (hydraulic machines and hydro power) and in SSC JE, mostly as direct questions on types, specific speed and efficiency.
What is the difference between fluid mechanics and hydraulics?
Fluid mechanics is the general theory for all fluids. Hydraulics is its practical side for water: pipes, channels, weirs, pumps and turbines. Exams list them separately but the principles are the same.
Which value of g and density should I use?
Use the values given in the question. If none are given, take g = 9.81 m/s² and the density of water as 1000 kg/m³.
Unlock an ad-free experience plus a growing library of ready-to-use civil-engineering calculators, IS-code cheat-sheets and formula PDFs. From just ₹99.




