Soil Mechanics Formulas for GATE, ESE and SSC JE: Formula Sheet with Solved Examples

Quick answer: Almost every soil mechanics question in GATE, ESE and SSC JE comes from ten areas: phase relations, index properties, permeability, effective stress, compaction, consolidation, shear strength, earth pressure, bearing capacity and piles. This page lists the formulas for each area in the order they are taught, with two solved examples.

Soil mechanics rewards students who know their formulas, because most questions are one or two steps long. The difficulty is that there are many formulas and several look alike. This sheet groups them by topic, states the units, and points out the places where marks are usually lost.

Use it for revision, not as a first reading. If a topic is new to you, read the linked guide first and come back here to memorise. For the other subjects, see the GATE, ESE and SSC JE preparation guide.

Phase relations

In simple words: Soil is a mixture of solid grains, water and air. Phase relations tell you how much of each is present and how heavy the soil is.

Civil Site Engineer Bundle — Concrete QC Handbook + RCC Lap Length Excel cover
📚 Recommended Download
Civil Site Engineer Bundle — Concrete QC Handbook + RCC Lap Length Excel
Our two best-sellers in one download: the 238-page Concrete Site Handbook kit plus the IS 456 lap-length Excel toolkit and quick-reference PDF.
✔ IS 456 based  ·  ✔ Instant download  ·  ✔ Lifetime access
₹1098₹299
Get the Bundle →

Where it is used: Working out the weight of fill behind a wall, checking the dry density achieved by a roller, and deciding how much water to add before compaction.

Treat soil as three phases: solids, water and air. Every relation below comes from the phase diagram, so if you forget one, take the volume of solids as 1 and derive it. Here γw is the unit weight of water (9.81 kN/m³, often taken as 10), G is the specific gravity of solids, e the void ratio, w the water content and S the degree of saturation.

QuantityFormula
Water contentw = Ww / Ws
Void ratioe = Vv / Vs
Porosityn = Vv / V = e / (1 + e)
Degree of saturationS = Vw / Vv
Key relationS e = w G
Bulk unit weightγ = (G + S e) γw / (1 + e)
Dry unit weightγd = G γw / (1 + e) = γ / (1 + w)
Saturated unit weightγsat = (G + e) γw / (1 + e)
Submerged unit weightγ′ = γsat − γw = (G − 1) γw / (1 + e)
Density index (relative density)Dr = (emax − e) / (emax − emin)

For typical values and more worked numbers, see unit weight of soil: types, formulas and values.

Index properties and classification

In simple words: These are simple laboratory numbers that tell you what kind of soil you have, before any strength test is done.

Where it is used: A clay with a high plasticity index, such as black cotton soil, swells when wet and shrinks when dry, so it needs special foundations. A well graded sand or gravel compacts well and makes good fill.

QuantityFormula
Plasticity indexPI = LL − PL
Liquidity indexLI = (w − PL) / PI
Consistency indexCI = (LL − w) / PI, so LI + CI = 1
ActivityA = PI / (% of clay finer than 2 µm)
Coefficient of uniformityCu = D60 / D10
Coefficient of curvatureCc = D30² / (D10 × D60)
A-line on the plasticity chartPI = 0.73 (LL − 20)
  • A gravel is well graded when Cu is more than 4, and a sand when Cu is more than 6. In both cases Cc must lie between 1 and 3.
  • Soils that plot above the A-line are clays; soils below it are silts or organic soils.
  • Activity below 0.75 is inactive clay, 0.75 to 1.25 is normal, and above 1.25 is active.

The tests behind LL, PL and SL are explained in Atterberg limits: liquid, plastic and shrinkage limit.

Permeability and seepage

In simple words: Permeability is how easily water flows through a soil. Gravel lets water through quickly; clay almost stops it.

Where it is used: Sizing the pumps to dewater an excavation, estimating seepage under a dam, and designing the drainage layer and weep holes behind a retaining wall.

QuantityFormula
Darcy’s lawv = k i, and q = k i A
Seepage velocityvs = v / n
Constant head testk = Q L / (A h t)
Falling head testk = 2.303 (a L / A t) log10(h1 / h2)
Flow parallel to layerskH = Σ(ki zi) / Σzi
Flow normal to layerskV = Σzi / Σ(zi / ki)
Seepage from a flow netq = k H (Nf / Nd) per unit length
Critical hydraulic gradientic = (G − 1) / (1 + e) = γ′ / γw

The constant head test suits coarse soils and the falling head test suits fine soils. For a layered deposit, kH is always greater than or equal to kV. Quick sand begins when the upward gradient reaches ic, which is close to 1 for most sands. See porosity vs permeability for the difference between the two terms.

Effective stress

In simple words: Part of the load in a saturated soil is carried by the grains and part by the water in the pores. Only the part carried by the grains, the effective stress, gives the soil its strength.

Where it is used: Lowering the water table by pumping increases effective stress and makes nearby buildings settle. Upward flow into an excavation reduces it and can turn sand into quick sand.

QuantityFormula
Total vertical stressσ = Σ(γ z) of all layers above the point
Pore water pressureu = γw hw
Effective stressσ′ = σ − u
With upward seepageσ′ = γ′ z − i z γw
With downward seepageσ′ = γ′ z + i z γw

Strength and settlement depend on effective stress, not total stress. Raising the water table above ground level does not change the effective stress in the soil below, because total stress and pore pressure rise by the same amount.

Compaction

In simple words: Compaction is packing soil tightly by rolling or ramming, so that air is pushed out. There is one water content at which a soil packs best.

Where it is used: Road embankments and backfill are specified as a percentage of the laboratory maximum dry density, commonly 95% or more, and checked layer by layer.

QuantityFormula or value
Dry unit weight from the testγd = γ / (1 + w)
Zero air voids lineγd = G γw / (1 + w G)
Light compaction, IS 2720 Part 72.6 kg rammer, 310 mm drop, 3 layers, 25 blows per layer
Heavy compaction, IS 2720 Part 84.9 kg rammer, 450 mm drop, 5 layers, 25 blows per layer

Both tests use a 1000 ml mould. Heavy compaction gives a higher maximum dry density at a lower optimum moisture content. The compaction curve can never cross the zero air voids line. The procedure and a full calculation are in the Proctor compaction test guide.

Consolidation

In simple words: When a saturated clay is loaded, water is squeezed out very slowly and the ground settles over months or years. That slow settlement is consolidation.

Where it is used: Buildings on soft clay keep settling long after construction. Engineers estimate how much and how fast, and sometimes preload the site or install drains to finish the settlement before building.

QuantityFormula
Compression index (normally consolidated clay)Cc = 0.009 (LL − 10)
Coefficient of volume compressibilitymv = av / (1 + e0)
Settlement from CcΔH = [Cc H / (1 + e0)] log10[(σ′0 + Δσ) / σ′0]
Settlement from mvΔH = mv Δσ H
Time factorTv = cv t / d²
Tv for U up to 60%Tv = (π / 4) U², with U as a fraction
Tv for U above 60%Tv = 1.781 − 0.933 log10(100 − U%)
Standard valuesT50 = 0.197 and T90 = 0.848
Coefficient of consolidationcv = k / (mv γw)
Over-consolidation ratioOCR = σ′c / σ′0

In the time factor, d is the length of the drainage path: the full thickness for single drainage and half the thickness for double drainage. A full settlement problem is solved in consolidation of soil: Terzaghi theory and settlement calculation.

Shear strength

In simple words: Shear strength is the resistance of a soil to sliding along a surface inside it. It comes from friction between grains and from cohesion.

Where it is used: Slopes, footings and retaining walls all fail by shear. The values c and φ from a triaxial or direct shear test go straight into bearing capacity and slope stability calculations.

QuantityFormula
Mohr-Coulomb failure criterionτf = c′ + σ′ tan φ′
Principal stresses at failureσ1 = σ3 tan²(45° + φ/2) + 2c tan(45° + φ/2)
Angle of the failure plane45° + φ/2 with the major principal plane
Unconfined compression testcu = qu / 2
SensitivitySt = qu (undisturbed) / qu (remoulded)
Vane shear test, both ends shearingT = π D² cu (H/2 + D/6)
Skempton’s pore pressure equationΔu = B [Δσ3 + A (Δσ1 − Δσ3)]
  • B is 1 for a saturated soil and 0 for a dry soil.
  • Triaxial tests: UU gives cu with φu = 0 for saturated clay; CU with pore pressure measurement and CD both give the effective parameters c′ and φ′.
  • A pure sand has c = 0, and a saturated clay in undrained loading has φ = 0.

Lateral earth pressure

In simple words: Soil pushes sideways on anything that holds it back. The push is smallest when the wall moves away from the soil (active) and largest when the wall is pushed into it (passive).

Where it is used: A cantilever retaining wall is designed for active pressure. A basement wall held by floor slabs cannot move, so it is designed for the higher at-rest pressure.

QuantityFormula
At rest (Jaky)K0 = 1 − sin φ
Active (Rankine)Ka = (1 − sin φ) / (1 + sin φ) = tan²(45° − φ/2)
Passive (Rankine)Kp = (1 + sin φ) / (1 − sin φ) = 1 / Ka
Active pressure at depth z in a c-φ soilpa = Ka γ z − 2c √Ka
Passive pressure at depth z in a c-φ soilpp = Kp γ z + 2c √Kp
Depth of tension crackzc = 2c / (γ √Ka)
Critical height of an unsupported vertical cutHc = 4c / (γ √Ka)
Total active thrust, dry cohesionless backfillPa = ½ Ka γ H², acting at H/3 above the base

For φ = 30°, Ka = 1/3, K0 = 0.5 and Kp = 3. Remember these three numbers. Worked examples are in Rankine earth pressure theory, and wall friction is covered in Coulomb earth pressure theory.

Bearing capacity and stress distribution

In simple words: Bearing capacity is the pressure a soil can carry under a footing without failing in shear or settling too much.

Where it is used: The plan size of a footing is the column load divided by the safe bearing capacity. A soil report that gives 150 kN/m² instead of 250 kN/m² makes every footing much larger.

QuantityFormula
Terzaghi, strip footingqu = c Nc + q Nq + 0.5 γ B Nγ
Terzaghi, square footingqu = 1.3 c Nc + q Nq + 0.4 γ B Nγ
Terzaghi, circular footingqu = 1.3 c Nc + q Nq + 0.3 γ B Nγ
Terzaghi factors for φ = 0Nc = 5.7, Nq = 1, Nγ = 0
Net ultimate bearing capacityqnu = qu − γ Df
Net safe bearing capacityqns = qnu / F
Safe bearing capacityqs = qnu / F + γ Df
Plate load test, clayqu (footing) = qu (plate); Sf / Sp = Bf / Bp
Plate load test, sandqu (footing) = qu (plate) × Bf / Bp
Plate load test, settlement in sandSf / Sp = [Bf (Bp + 0.3) / (Bp (Bf + 0.3))]², widths in metres
Boussinesq, point load Qσz = [3Q / (2π z²)] × 1 / [1 + (r/z)²]5/2
Boussinesq, directly below the loadσz = 0.4775 Q / z²

In these equations q = γ Df is the overburden pressure at the base of the footing and B is its width (the diameter for a circular footing). The factor of safety F is usually 2.5 to 3. See bearing capacity: Terzaghi vs Meyerhof for the theory and safe bearing capacity values for typical numbers.

Pile foundations

In simple words: When the soil near the surface is too weak, piles carry the load down to stronger soil, partly on their tip and partly by friction along their sides.

Where it is used: Bridges, tall buildings on soft clay and structures over water. Pile capacity is estimated by formula first and then confirmed by a load test on site.

QuantityFormula
Ultimate capacity of a pileQu = Qp + Qs
End bearing in clayQp = 9 cu Ap
Skin friction in clayQs = α cu As
Group efficiencyη = Qgroup / (n × Qsingle)
Group in clay, block failureQg = 9 cu Ablock + cu × perimeter of block × L

Here α is the adhesion factor, close to 1 for soft clay and lower for stiff clay. The capacity of a group in clay is the smaller of the block failure value and n times the single pile capacity. More in pile foundation design: types and load capacity.

Solved example 1: phase relations

Question. A soil has a bulk unit weight of 18 kN/m³ and a water content of 20%. The specific gravity of solids is 2.7. Find the dry unit weight, the void ratio and the degree of saturation. Take γw = 9.81 kN/m³.

  • Dry unit weight: γd = γ / (1 + w) = 18 / 1.20 = 15 kN/m³.
  • Void ratio: γd = G γw / (1 + e), so 1 + e = 2.7 × 9.81 / 15 = 1.766 and e = 0.766.
  • Degree of saturation: S = w G / e = 0.20 × 2.7 / 0.766 = 0.705, or 70.5%.

Solved example 2: time for consolidation

Question. A clay layer 4 m thick lies between two sand layers. Its coefficient of consolidation is 3 m²/year. How long does it take to reach 50% consolidation?

  • Sand above and below means double drainage, so d = 4 / 2 = 2 m.
  • For U = 50%, Tv = 0.197.
  • t = Tv d² / cv = 0.197 × 2² / 3 = 0.263 year, which is about 96 days.

If the same layer drained on one side only, d would be 4 m and the time would be four times longer.

Common mistakes

  • Using the full layer thickness as the drainage path when the layer is drained on both sides.
  • Putting water content or degree of saturation into a formula as a percentage instead of a fraction.
  • Using γsat below the water table where the submerged unit weight γ′ is needed, for example in the third term of the bearing capacity equation.
  • Mixing up net ultimate, net safe and safe bearing capacity. Divide only the net value by the factor of safety, then add γ Df back if the gross safe value is asked.
  • Forgetting the 2c√Ka term for a cohesive backfill, or giving it the wrong sign.
  • Mixing units: k in cm/s with lengths in metres, or cv in cm²/s with time in years.

Frequently asked questions

Which soil mechanics topics are most important for GATE?

Consolidation, shear strength, effective stress with seepage, earth pressure and bearing capacity produce most of the numerical questions. Phase relations and index properties are the easiest marks, so do not skip them.

Is the same formula sheet enough for SSC JE?

Yes. SSC JE asks direct questions from the same formulas and adds more questions on definitions, test names and IS classification. Learn the tables on this page and the standard test details, and the subject is covered.

What value of the unit weight of water should I use?

Use the value given in the question. If none is given, 9.81 kN/m³ is the standard value. Many questions say to take 10 kN/m³ to simplify the arithmetic.

What is the difference between consolidation and compaction?

Compaction is the quick removal of air from a soil by mechanical effort, with the water content unchanged. Consolidation is the slow squeezing out of water from a saturated soil under a sustained load. Compaction is done on purpose during construction; consolidation happens on its own afterwards.

Stop calculating by hand — go Pro

Unlock an ad-free experience plus a growing library of ready-to-use civil-engineering calculators, IS-code cheat-sheets and formula PDFs. From just ₹99.

Go Pro →
Fuel Free Learning Support TheCivilStudies

Keep civil engineering knowledge free — articles, calculators, and practical site guides for everyone.

Choose an amount

100% Secure · Powered by Cashfree

TheCivilStudies Team
TheCivilStudies Team

TheCivilStudies is an independent civil-engineering learning site from India. Our guides explain IS-code provisions, formulas, worked examples and site practice for students and working site engineers. Calculations are checked against the relevant Indian Standard, and articles are updated when codes or practice change. Spotted an error? Tell us in the comments and we will fix it.

Articles: 459