Solid Mechanics (Strength of Materials) for GATE, ESE and SSC JE: Every Syllabus Topic Explained with Examples

Quick answer: Solid mechanics, also called strength of materials, explains how a member stretches, bends, twists or buckles under load. The GATE syllabus lists seven ideas: shear force and bending moment, stress and strain, bending stress, shear stress, torsion, transformation of stress and column buckling. This page explains each one in plain language, with the formula, a site example and a solved problem.

Strength of materials is the first subject to study for any civil engineering exam, because structural analysis, RCC design and steel design are all built on it. If you understand why a beam bends and where it is stressed most, half of structural engineering becomes easier.

The topics below follow the order of the official GATE Civil Engineering syllabus under “Solid Mechanics”, with the extra topics that ESE and SSC JE ask added at the end. Forces are in N or kN, lengths in mm or m, and stresses in N/mm² (the same as MPa). For the other subjects, see the GATE, ESE and SSC JE preparation guide.

What the syllabus asks

ExamSyllabus wording
GATE CE (Structural Engineering section)Bending moment and shear force in statically determinate beams; simple stress and strain relationships; simple bending theory, flexural and shear stresses, shear centre; uniform torsion; transformation of stress; buckling of column; combined and direct bending stresses
ESE Civil Paper IElastic constants, stress, plane stress, strains, plane strain, Mohr’s circle of stress and strain, elastic theories of failure, principal stresses, bending, shear and torsion
SSC JE (Theory of Structures)Elastic constants, types of beams, bending moment and shear force diagrams, moment of area and moment of inertia, bending and shear stresses, slope and deflection, torsion of circular section, critical load for columns

The wording differs, but the concepts are the same. Learn them once in the order below.

Civil Site Engineer Bundle — Concrete QC Handbook + RCC Lap Length Excel cover
📚 Recommended Download
Civil Site Engineer Bundle — Concrete QC Handbook + RCC Lap Length Excel
Our two best-sellers in one download: the 238-page Concrete Site Handbook kit plus the IS 456 lap-length Excel toolkit and quick-reference PDF.
✔ IS 456 based  ·  ✔ Instant download  ·  ✔ Lifetime access
₹1098₹299
Get the Bundle →

1. Stress and strain

In simple words: Stress is the internal force a material carries on each unit of its area. Strain is how much it deforms compared with its original size. Stress tells you how hard the material is working; strain tells you how much it has moved.

Where you see it: A steel bar in a slab is pulled when the slab bends. The pull divided by the bar area is the stress in the bar. A column under a building is pushed; the load divided by the column area is its compressive stress.

QuantityFormula
Normal stressσ = P / A
Normal strainε = δ / L
Hooke’s law (within the elastic limit)σ = E ε
Change in length of a barδ = P L / (A E)
Tapering circular bar, diameters d1 and d2δ = 4 P L / (π E d1 d2)
Bar hanging under its own weightδ = γ L² / (2E) = W L / (2 A E)
Thermal stress, ends fully heldσ = E α ΔT
Strain energy stored per unit volumeσ² / (2E)

E is the modulus of elasticity: about 2 × 105 N/mm² for steel. A material with a high E is stiff, not necessarily strong. The stages a steel bar goes through before it breaks are shown in the stress-strain curve of mild steel, and the basic ideas are covered in what is stress.

Example. A steel bar of 20 mm diameter and 2 m length carries a pull of 50 kN. Find the stress and the extension. E = 2 × 105 N/mm².

  • Area A = π × 20² / 4 = 314.2 mm².
  • Stress σ = 50 000 / 314.2 = 159.2 N/mm².
  • Extension δ = P L / (A E) = 50 000 × 2000 / (314.2 × 2 × 105) = 1.59 mm.

Thermal stress in practice. A bar that is free to expand has no stress, however hot it gets. Stress appears only when the expansion is prevented. A steel rail held at both ends and heated by 30°C develops σ = 2 × 105 × 12 × 10−6 × 30 = 72 N/mm². This is why long bridges and buildings are given expansion joints.

2. Elastic constants

In simple words: A material can be deformed in three ways: stretched, sheared or squeezed from all sides. Each has its own stiffness: E for stretching, G for shearing and K for change of volume. Poisson’s ratio μ links them: when you stretch a bar, it also becomes thinner, and μ is the ratio of the sideways strain to the lengthwise strain.

QuantityFormula
Poisson’s ratioμ = lateral strain / longitudinal strain
E and GE = 2G (1 + μ)
E and KE = 3K (1 − 2μ)
E, G and K togetherE = 9KG / (3K + G)
Volumetric strain of a bar under axial stressεv = (σ / E)(1 − 2μ)
  • μ lies between 0 and 0.5. It is about 0.3 for steel, 0.15 to 0.2 for concrete and close to 0.5 for rubber.
  • An isotropic material has only two independent elastic constants. Given any two, you can find the others.
  • At μ = 0.5 the volume does not change under load.

For concrete, E depends on the grade. See modulus of elasticity of concrete.

3. Shear force and bending moment

In simple words: Cut a loaded beam at any point. The shear force is the net up-or-down force on one side of the cut, which tries to slide one part past the other. The bending moment is the net turning effect of the forces on one side, which tries to bend the beam.

Where you see it: The bending moment diagram tells the designer where to put the main bars and how many. A simply supported slab has its largest moment at mid-span, so the main steel is at the bottom there. A cantilever balcony has its largest moment at the support with tension on top, so its main steel goes at the top. Placing balcony steel at the bottom is a classic site mistake that leads to collapse.

RelationMeaning
dV/dx = −wThe slope of the shear force diagram equals the load intensity
dM/dx = VThe slope of the bending moment diagram equals the shear force
V = 0The bending moment is maximum or minimum at this point
M = 0 with a change of signPoint of contraflexure
Beam and loadingMaximum momentMaximum deflectionMaximum slope
Cantilever, point load W at the free endW L at the supportW L³ / (3EI)W L² / (2EI)
Cantilever, UDL w per metrew L² / 2 at the supportw L⁴ / (8EI)w L³ / (6EI)
Simply supported, point load W at the centreW L / 4 at the centreW L³ / (48EI)W L² / (16EI)
Simply supported, UDL w per metrew L² / 8 at the centre5 w L⁴ / (384EI)w L³ / (24EI)
Fixed at both ends, point load W at the centreW L / 8 at the supports and at the centreW L³ / (192EI)Zero at the supports
Fixed at both ends, UDL w per metrew L² / 12 at the supports, w L² / 24 at the centrew L⁴ / (384EI)Zero at the supports

Fixing the ends of a beam cuts the mid-span moment and reduces the deflection under a UDL to one-fifth. For a propped cantilever with a UDL, the prop carries 3wL/8 and the moment at the fixed end is wL²/8. The comparison is explained in fixed beams vs simply supported beams, and you can draw the diagrams for any loading with the beam analysis calculator.

4. Simple bending theory and flexural stress

In simple words: When a beam bends downward, its top fibres are squeezed and its bottom fibres are stretched. Somewhere in between is a layer that is neither squeezed nor stretched: the neutral axis. The stress is zero there and grows in a straight line to its largest value at the top and bottom faces.

Where you see it: This is why an I-section is efficient: most of its material sits in the flanges, far from the neutral axis, where the stress is highest. It is also why concrete beams have steel at the tension face. Concrete near the neutral axis does very little work.

QuantityFormula
Bending equationM / I = σ / y = E / R
Maximum bending stressσmax = M / Z, where Z = I / ymax
Rectangle b × dI = b d³ / 12, Z = b d² / 6
Solid circle of diameter dI = π d⁴ / 64, Z = π d³ / 32
Triangle of base b and height hI = b h³ / 36 about the centroidal axis, b h³ / 12 about the base
Parallel axis theoremI = IG + A h²

Because Z depends on d², depth is worth far more than width. A 230 × 450 mm beam placed upright is nearly twice as strong in bending as the same section laid flat.

5. Shear stress in beams and shear centre

In simple words: Shear stress in a beam is not uniform over the depth. It is zero at the top and bottom faces and largest at or near the neutral axis, the opposite of bending stress.

QuantityFormula
Shear stress at a level in the sectionτ = V A ȳ / (I b)
Average shear stressτavg = V / (area of section)
Rectangleτmax = 1.5 τavg, at the neutral axis
Solid circleτmax = (4/3) τavg, at the neutral axis
Triangleτmax = 1.5 τavg at mid-height; (4/3) τavg at the neutral axis

In the formula, A is the area above the level considered, ȳ is the distance of its centroid from the neutral axis, and b is the width at that level. In an I-section the web carries most of the shear and the flanges carry most of the bending.

Shear centre. It is the point through which a transverse load must pass so that the beam bends without twisting. For a section with two axes of symmetry it is at the centroid. For a channel section it lies outside the web, on the side away from the flanges, which is why a channel loaded through its web twists.

Example. A simply supported beam of 6 m span carries a UDL of 20 kN/m. The section is 300 mm wide and 500 mm deep. Find the maximum bending stress and the maximum shear stress.

  • Maximum moment M = w L² / 8 = 20 × 6² / 8 = 90 kN·m = 90 × 106 N·mm.
  • Section modulus Z = b d² / 6 = 300 × 500² / 6 = 12.5 × 106 mm³.
  • Bending stress σ = M / Z = 90 × 106 / (12.5 × 106) = 7.2 N/mm², at mid-span, top and bottom faces.
  • Maximum shear V = w L / 2 = 60 kN, at the supports.
  • τavg = 60 000 / (300 × 500) = 0.4 N/mm², so τmax = 1.5 × 0.4 = 0.6 N/mm², at the neutral axis near the supports.

6. Uniform torsion

In simple words: Torsion is twisting. When a shaft is twisted, each cross-section rotates a little relative to the next, and shear stress develops. The stress is zero at the centre and largest at the outer surface.

Where you see it: An edge beam that supports a slab on one side only, a beam curved in plan, and the beam that carries a cantilever canopy are all twisted as well as bent. In machines, every shaft that transmits power is in torsion.

QuantityFormula
Torsion equationT / J = τ / r = G θ / L
Polar moment of inertia, solid shaftJ = π d⁴ / 32
Polar moment of inertia, hollow shaftJ = π (D⁴ − d⁴) / 32
Maximum shear stress, solid shaftτmax = 16 T / (π d³)
Power transmittedP = 2π N T / 60, with N in rpm, T in N·m and P in watts
Torsional rigidityG J

A hollow shaft is stronger than a solid shaft of the same weight, because the material near the centre of a solid shaft carries very little stress.

Example. A solid shaft of 60 mm diameter carries a torque of 2 kN·m. Find the maximum shear stress.

  • τmax = 16 T / (π d³) = 16 × 2 × 106 / (π × 60³) = 47.2 N/mm², at the surface.

7. Transformation of stress and principal stresses

In simple words: The stresses at a point depend on the direction of the plane you look at. On certain planes there is no shear stress at all, only direct stress. These are the principal planes, and the stresses on them, the principal stresses, are the largest and smallest direct stresses at that point.

Where you see it: Concrete is weak in tension and cracks at right angles to the largest tensile principal stress. Near the supports of a beam, where shear is high, that direction is inclined, which is why shear cracks run diagonally at about 45°. Stirrups are placed to cross those cracks.

QuantityFormula
Principal stressesσ1,2 = (σx + σy) / 2 ± √{[(σx − σy) / 2]² + τxy²}
Direction of the principal planestan 2θp = 2 τxy / (σx − σy)
Maximum in-plane shear stressτmax = (σ1 − σ2) / 2
Mohr’s circleCentre at (σx + σy) / 2; radius equal to τmax
  • The planes of maximum shear are at 45° to the principal planes.
  • σ1 + σ2 = σx + σy always.
  • Under pure shear τ, the principal stresses are +τ and −τ on planes at 45°.

Example. At a point σx = 80 N/mm², σy = 20 N/mm² (both tensile) and τxy = 40 N/mm². Find the principal stresses and the maximum shear stress.

  • Centre of Mohr’s circle = (80 + 20) / 2 = 50 N/mm².
  • Radius = √(30² + 40²) = 50 N/mm².
  • σ1 = 50 + 50 = 100 N/mm² and σ2 = 50 − 50 = 0.
  • τmax = 50 N/mm².

8. Buckling of columns

In simple words: A short, thick column fails when the material is crushed. A long, thin column fails earlier by bending sideways, even though the stress in it is small. That sideways failure is buckling. Press a plastic ruler from its ends and you will see it.

Where you see it: Scaffolding pipes and formwork props are slender, so they are braced at intervals to shorten their effective length. Halving the unbraced length makes a slender prop four times stronger against buckling. Many formwork collapses begin with missing bracing.

QuantityFormula
Euler’s critical loadPcr = π² E I / Le²
Slenderness ratioλ = Le / r, where r = √(I / A)
Rankine’s formulaP = σc A / (1 + a λ²)
End conditionsEffective length LeLoad compared with both ends hinged
Both ends hingedL1
One end fixed, the other free2L¼
Both ends fixedL / 24
One end fixed, the other hingedL / √22

Euler’s formula is valid only for long columns. Use the least moment of inertia of the section, because the column buckles about its weakest axis. Rankine’s formula covers short, medium and long columns.

9. Combined direct and bending stresses

In simple words: If a load on a column is not at the centre, it presses the column and bends it at the same time. One face is squeezed more than the other. If the load is far enough from the centre, the far face goes into tension.

Where you see it: Masonry walls, brick piers, plain concrete footings and gravity dams cannot take tension. They are proportioned so that the resultant load stays inside the middle third of the base. This is the “middle third rule”.

QuantityFormula
Stress at the extreme facesσ = P / A ± M / Z, with M = P e
No tension in a rectangular sectione ≤ b / 6 (load within the middle third)
No tension in a solid circular sectione ≤ d / 8 (load within the middle quarter)

Example. A 300 × 600 mm column carries 600 kN at an eccentricity of 50 mm along the 600 mm side. Find the stresses at the two faces.

  • Direct stress = 600 000 / (300 × 600) = 3.33 N/mm².
  • Moment M = 600 000 × 50 = 30 × 106 N·mm. Z = 300 × 600² / 6 = 18 × 106 mm³. Bending stress = 1.67 N/mm².
  • Maximum stress = 3.33 + 1.67 = 5.0 N/mm². Minimum stress = 3.33 − 1.67 = 1.67 N/mm², still compressive.
  • Check: e = 50 mm is less than 600 / 6 = 100 mm, so there is no tension, as expected.

10. Extra topics for ESE and SSC JE

TopicFormula
Thin cylinder, hoop stressσh = p d / (2t)
Thin cylinder, longitudinal stressσl = p d / (4t)
Thin spherical shellσ = p d / (4t)
Closed-coil helical spring, deflectionδ = 8 W D³ n / (G d⁴)
Closed-coil helical spring, stiffnessk = G d⁴ / (8 D³ n)
Load applied suddenlyStress is twice the stress under the same load applied gradually

A cylinder is “thin” when its wall thickness is less than about one-twentieth of its diameter. The hoop stress is twice the longitudinal stress, so a pipe or a water tank under pressure splits along its length. That is why circular water tanks have their main steel as horizontal rings. ESE also asks the theories of failure: maximum principal stress (Rankine), maximum shear stress (Tresca), maximum strain energy (Haigh) and maximum distortion energy (von Mises).

Common mistakes

  • Mixing units: a moment in kN·m with a section modulus in mm³. Convert the moment to N·mm first.
  • Using the full length instead of the effective length in Euler’s formula.
  • Using the larger moment of inertia for buckling. A column buckles about the axis with the smaller I.
  • Placing the maximum shear stress at the top or bottom face. It is at or near the neutral axis.
  • Forgetting that a temperature change causes no stress in a bar that is free to expand.
  • Reading the fixed beam moment for a UDL as wL²/8. That is the simply supported value; a fixed beam has wL²/12 at the supports and wL²/24 at mid-span.

Frequently asked questions

Is solid mechanics the same as strength of materials?

Yes. GATE and ESE call it solid mechanics, most textbooks call it strength of materials or mechanics of materials, and SSC JE places it under theory of structures. The content is the same.

How should I study this subject for GATE?

Take one topic at a time in the order above. Understand the idea, learn the formula, then solve previous years’ questions on that topic before moving on. Shear force and bending moment diagrams, principal stresses and deflection are asked most often, and they also appear inside structural analysis questions.

Do I need to learn derivations?

Not for GATE or SSC JE, which are objective. For ESE Mains you should be able to derive the bending equation, the torsion equation and Euler’s formula, and to draw Mohr’s circle neatly.

Which book is enough?

Any standard textbook on strength of materials that you have already used in college is enough, as long as you finish it and solve its problems. Changing books late in your preparation costs more than it gives.

Stop calculating by hand — go Pro

Unlock an ad-free experience plus a growing library of ready-to-use civil-engineering calculators, IS-code cheat-sheets and formula PDFs. From just ₹99.

Go Pro →
Fuel Free Learning Support TheCivilStudies

Keep civil engineering knowledge free — articles, calculators, and practical site guides for everyone.

Choose an amount

100% Secure · Powered by Cashfree

TheCivilStudies Team
TheCivilStudies Team

TheCivilStudies is an independent civil-engineering learning site from India. Our guides explain IS-code provisions, formulas, worked examples and site practice for students and working site engineers. Calculations are checked against the relevant Indian Standard, and articles are updated when codes or practice change. Spotted an error? Tell us in the comments and we will fix it.

Articles: 456